Tunnel heater hose [6.5 hours]

Some time ago I added some brackets to the front of the tunnel, so I could secure the rear heater hose. With Control Approach rudder pedals, the hose needs to be secured in the center of the tunnel, clear of the control arms off to each side of the tunnel. I was going to use a 2″ Adel clamp around the scat tube, based on what another RV-10 builder had done.

After assembling this, I didn’t like it because:

  • It was difficult to install the Adel clamp, while lying on my stomach with the seats removed and reaching in under the panel. The rear heater hose has to be sort-of scrunched against the short front heater hose in order to get it positioned in the middle of the tunnel.
  • The large Adel clamp, held by a single bolt, was not very secure and could have a tendency to rotate over time
  • If anything came undone over time, the compacted rear heater hose would push loose items towards the rear, straight into the rudder pedal arms.
  • I still had to come up with a solution to replace the standard F-1051J Scat tube support, since this support interferes with the internally run rudder cables when the Control Approach rudder pedals are used.

After a few minutes pondering these problems, the solution hit me – design and 3D print a pair of Nylon brackets to retain the scat tube. The brackets then simply slide onto the scat tube from the rear. For the front bracket, I bolted the Nylon piece to the Aluminium angle retainer on the bench, slid it onto the scat tube, lifted the rudder pedal arms, positioned the bracket assembly and screwed it into position. I also drilled a pair of small holes into the Aluminium angle in order to add a safety wire each side, that way if the brackets ever came loose for any reason, the assembly could not fall aft and interfere with the rudder pedal arms.

For the aft bracket, I had already a long time ago drilled and dimpled the holes on the right hand side of the tunnel for the standard F-1051J scat tube bracket. The lower of these two holes is close to the right hand rudder cable. It would have been better to raise this hole by about 1/2″, but that is ancient history. I resolved this by using a low profile (AN364) lock nut and embedding the nut into a hexagonal cutout in the bracket, as shown in the pictures. I used a pair of 0.063″ shims on each side, with the holes countersunk, to complete the assembly.

It all worked great, both brackets can be easily removed and reinstalled, so any future maintenance that requires removing the rear heater hose for better tunnel access will be easy.

PostScript:

A couple of other RV-10 builders have asked me for the models, and one questioned why I elected to use the metal shims on the aft bracket. I used the shims simply because I didn’t think my consumer grade 3D printer could do a good enough job of the countersinks, when printing them in Nylon, vertically. In any case, I added an option to the model to have no shims, which widens the aft bracket to compensate for the missing shims, and adds countersinks to the sides to allow for the #8 dimples in the tunnel walls. I’ve added pictures of this version. The three STL files can be downloaded using the following link:

Download

 

  • front_heater_bracket
    front_heater_bracket
    Front scat tube bracket
  • aft_heater_bracket
    aft_heater_bracket
    Aft scat tube bracket, replaces F-1051J
  • f47a
    f47a
    Front Scat tube bracket assembly
  • f47b
    f47b
    Aft scat tube bracket, replaces F-1051J
  • no_shim1
    no_shim1
    Aft bracket "no shim" version, with included countersinks
  • no_shim2
    no_shim2
    Aft bracket "no shim" version, with included countersinks
  • no_shim3
    no_shim3
    Side slopes to match tunnel
Bookmark the permalink.

Comments are closed.